Official firmware for htc one. Firmware for HTC One M7? Is it worth switching to MIUI

Every smartphone owner wants to make their device better, turn it into a more functional and modern solution. If the user cannot do anything with the hardware, then anyone can improve the software. HTC One X is a high-end phone with excellent technical characteristics. How to reinstall or replace the system software on this device will be discussed in the article.

Considering the NTS One X from the point of view of the firmware capabilities, it should be noted that the device in every possible way “resists” interference in its software part. This state of affairs is due to the manufacturer’s policy, therefore, before installing the firmware, you should pay special attention to studying the concepts and instructions and only after fully understanding the essence of the processes proceed to direct manipulations with the device.

Every action carries a potential danger to the device! Responsibility for the results of manipulations with the smartphone lies entirely with the user who carries them out!

As with other Android devices, the success of HTC One X firmware procedures is largely determined by proper preparation. We carry out the following preparatory operations, and before carrying out actions with the device, we thoroughly study the proposed instructions, download the necessary files, and prepare the tools that are supposed to be used.

Drivers

The easiest way to add components to the system for interacting software tools with One X memory sections is to install HTC Sync Manager, the manufacturer’s proprietary program for working with your smartphones.

Backing up information

Using the methods described below for installing system software into the device in question involves erasing user data contained in the smartphone. After installing the OS, you will have to restore the information, which is impossible without a previously created backup. The official way to save data is as follows.

Necessary

To operate with HTC One X memory partitions, in addition to drivers, the PC as a whole will need functional and convenient software tools. Be sure to download and unpack the package with and into the root of drive C:. Below in the description of methods we will not dwell on this issue, implying that Fastboot is present in the user’s system.

Run in different modes

To install various system software, you will need to switch the phone to special operating modes - "BootLoader" And "Recovery".

Unlocking the bootloader

The instructions for installing modified firmware below assume that the device's bootloader is unlocked. It is recommended to carry out the procedure in advance, and this is done using the official method offered by HTC. And it is also assumed that before performing the following, Sync Manager and Fastboot are installed on the user’s computer, and the phone is fully charged.

1. Follow the link to the official website of HTC Developer Center and press the button "Register".



2. Fill out the form fields and press the green button "Register".



3. Go to your mail, open the letter from the HTCDev team and click on the link to activate your account.



4. After activating your account, enter your username and password into the appropriate fields on the HTC Developer Center web page and click "Login".



5. In area "Unlock bootloader" click "Get Started".



6. On the list "Supported Devices" you need to select all supported models and then use the button "Begin Unlock Bootloader" to proceed to further steps.



7. We confirm our awareness of the potential danger of the procedure by clicking "Yes" in the request window.



8. Next, check both checkboxes and press the button to go to unlocking instructions.



9. In the instructions that open, skip all the steps

   

   and scroll through the instructions to the very end. We only need a field to insert an identifier.



10. We put the phone into mode "Bootloader". In the list of commands that opens, select "FASTBOOT", then connect the device to the PC using a USB cable.



11. Open the command line and write the following:

    cd C:\ADB_Fastboot

    

12. The next step is to find out the device ID value required to obtain unlock permission from the developer. To obtain information, you need to enter the following in the console:

    fastboot oem get_identifier_token

    

    and start executing the command by pressing "Enter".

13. Select the resulting set of characters using the arrow buttons on the keyboard or with the mouse,

    

    and copy the information (using the combination "Ctrl" + "WITH") in the appropriate field on the HTCDev web page. It should look like this:

    

    To go to the next step, click "Submit".

14. If the above steps are completed successfully, we receive an email from HTCDev containing Unlock_code.bin– a special file for transferring to the device. Download the file from the letter and place the downloaded file in the Fastboot directory.



15. We send the command via the console:

    fastboot flash unlocktoken Unlock_code.bin



16. Executing the command above will result in a prompt appearing on the device screen: "Unlock bootloader?". Place a mark next to "Yes" and confirm readiness to start the process using the button "Inclusion" on the device.



17. As a result, the procedure will continue and the Bootloader will be unlocked.



18. Confirmation of successful unlocking is the inscription "***UNLOCKED***" at the top of the main mode screen "Bootloader".

Installing custom recovery

For any serious manipulations with the HTC One X system software, you will need a modified recovery environment (custom recovery). Provides a lot of possibilities for the model in question. Let's install one of the ported versions of this recovery environment into the device.

Firmware

In order to bring certain improvements to the software part of the device in question, upgrade the Android version to a more or less current one, and also diversify the functionality, you should resort to using unofficial firmware.

To install custom and ports, you will need a modified environment, which can be installed according to the instructions above in the article, but first you can simply update the version of the official software.

Method 1: Android application “Software Updates”

The only method of working with the smartphone system software officially approved by the manufacturer is to use the tool built into the official firmware "Software Updates". During the life cycle of the device, that is, while system updates were released from the manufacturer, this feature regularly reminded itself of itself with persistent notifications on the device screen.

Today, in order to update the official version of the OS or make sure the latest one is up to date, you need to do the following.

Method 2: Android 4.4.4 (MIUI)

Software from third-party developers can breathe new life into your device. The choice of a modified solution lies entirely with the user; the available set of different packages for installation is quite wide. As an example, below we use the firmware ported by the MIUI Russia team for HTC One X, which is based on Android 4.4.4.

1. We install the modified recovery using the method described above in the preparatory procedures.
2. Download the software package from the official web resource of the MIUI Russia team:



3. Place the zip package in the internal memory of the device.



Additionally. If the smartphone does not boot into Android, which makes it impossible to copy packages into memory for further installation, you can use OTG capabilities. That is, copy the package from the OS to a USB flash drive, connect it via an adapter to the device and, during further manipulations in recovery, indicate the path to "OTG-Flash".

4. Loading the phone into "Bootloader", further in "RECOVERY". And we ALWAYS make a backup by selecting the corresponding items in CWM one by one.



5. We do wipes (cleaning) of the main system partitions. To do this you will need an item "wipe data/factory reset".



6. Let's go to "install zip" on the main CWM screen, indicate to the system the path to the zip package with the software, after selecting “choose zip from storage/sdcard” and start installing MIUI by clicking “Yes – Install...”.



7. We are waiting for the success confirmation message to appear - "Install from sd card complete", return to the main screen of the environment and select "advanced", and then reboot the device into Bootloader.



8. Unpack the firmware with an archiver and copy it boot.img to the catalog from Fastboot.



9. We put the device into mode "FASTBOOT" from the Bootloader, connect it to the PC if it was disconnected. Run the Fastboot command line and flash the image boot.img:
   fastboot flash boot boot.img

   

10. Reboot into the updated Android using the item "REBOOT" on the menu "Bootloader".



11. You will have to wait a bit for the MIUI 7 components to initialize, and then carry out the initial system setup.

    

    It is worth noting that MIUI on HTC One X works very well.

Method 3: Android 5.1 (CyanogenMod)

In the world of Android devices, there are not many smartphones that have successfully performed their functions for more than 5 years and at the same time are popular with enthusiastic developers who successfully continue to create and port firmware based on new versions of Android.

Probably, HTC One X owners will be pleasantly surprised that a fully functional Android 5.1 can be installed on the device, but by doing the following, we get exactly this result.

Step 1: Install TWRP and new partition

Among other things, Android 5.1 brings with it the need to re-partition the device’s memory, that is, change the size of partitions to achieve better results in terms of stability and the ability to perform functions added by developers to the new version of the system. You can repartition and install a custom one based on Android 5 only using a special version.

Step 2: Installation of custom

So, the new markup is already installed on the phone, you can proceed to installing custom firmware with Android 5.1 as the basis. Let's install CyanogenMod 12.1 - an unofficial firmware port from a team that needs no introduction.

• "Platform" - "ARM";
• "Andriod" — "5.1";
• "Variant" - "nano".

To start downloading, press the round button with the image of an arrow pointing down.

Unpack the package cm-12.1-20160905-UNOFFICIAL-endeavoru.zip and move boot.img from it to the catalog with Fastboot.

Method 4: Official firmware

If there is a desire or need to return to the official firmware from HTC after installing custom ones, you need to again turn to the capabilities of modified recovery and Fastboot.

1. Download the version of TWRP for the “old markup” and place the image in the Fastboot folder.
2. Download the package with the official firmware. The link below is OS for the European region version 4.18.401.3.
3. Download the image of the HTC factory recovery environment.
4. Unpack the archive with the official firmware and copy it boot.img from the resulting directory to the folder with Fastboot.

   

   We put the file there recovery_4.18.401.3.img.img, containing stock recovery.



5. We flash boot.img from the official firmware via Fastboot.
   fastboot flash boot boot.img



6. Next, install TWRP for the old markup.

   fastboot flash recovery twrp2810.img



7. We disconnect the device from the PC and reboot into the modified recovery environment. Then we go the next way. "Wipe" - "Advanced Wipe"- mark the section "sdcard" - "Repair or Change File System". We confirm the start of the process of changing the file system with the button "Change File System".



8. Next, press the button "FAT" and move the switch "Swipe to Change", and then wait for the formatting to finish and return to the TWRP main screen using the button "Home".



9. Select an item "Mount", and on the next screen - "Enable MTP".



10. Mounting done in the previous step will allow the smartphone to be identified in the system as a removable drive. We connect One X to the USB port and copy the zip package with the official firmware to the internal memory of the device.



11. After copying the package, click "Disable MTP" and return to the main recovery screen.



12. We clean all partitions except "sdcard", going through the points: "Wipe" - "Advanced Wipe"- selection of sections – "Swipe to Wipe".



13. Everything is ready to install the official firmware. Choose "Install", indicate the path to the package and begin installation by sliding the switch "Swipe to Confirm Flash".



14. Button "Reboot System", which will appear after the firmware is completed, will reboot the smartphone into the official version of the OS; you just need to wait for the latter to initialize.



15. If desired, you can restore the factory recovery with the standard Fastboot command:

    fastboot flash recovery recovery_4.18.401.3.img

    And also block the bootloader:

    fastboot oem lock

16. Thus, we get a completely reinstalled official version of the software from HTC.

In conclusion, I would like to once again note the importance of scrupulously following the instructions when installing system software on the HTC One X. Carry out the firmware carefully, evaluating each step before implementing it, and achieving the desired result is guaranteed!

Almost every user of HTC phones on the Android platform is faced with the need to flash their own gadget. This allows you to rid your phone of many problems and freezes, improve performance and change the interface.

However, this is quite difficult to do. In our article we will tell you how to flash htc android yourself.

Preparing your phone

Initially, the phone needs to be prepared for firmware. To do this you need to do the following:

1. Get ROOT rights. To do this, you need to download and install the z4root program.
2. Download the Unrevoked program.
3. Turn off Desire and run it in HBOOT menu mode. To do this, press the Volume Down and Power keys simultaneously.
4. Connect the phone to the computer using a USB cable (you need to wait for the next text message to appear - HBOOT USB PLUG).
5. Open "Device Manager".

If you did everything correctly, you will see an unidentified Android device there. Right-click on it and select “Update Drivers”.

To exit the HBOOT menu, you need to turn off the phone and then start it in standard mode.

Main part

1. Download the required firmware. It is recommended to download the necessary files from the official website htc.com.
2. Save all important information on your gadget. Please note that you can use the Titanium Backup utility to back up files and programs.
3. Charge your phone (at least 60%).
4. Clear all user information. To do this, you need to go to “Settings” through the phone interface, and then select “Privacy” and “Reset data”. This is required to ensure that there is no mismatch between the firmware modules.

Installation

1. In recovery, select “install zip from sd-card”.
2. Find the downloaded zip firmware.
3. Let's launch the program. If everything is fine, the installation will begin and you will see the appropriate messages. When the firmware is finished, you will see the inscription “Installation completed”.
4. Reboot your phone and wait for the download to start.

As practice shows, you can flash an HTC in fifteen to thirty minutes. The first start after this operation may take a long time. Don't worry about this. If you do everything correctly, you will get the latest version of Android.

Possible risks

If you plan to flash your device yourself, without resorting to the help of specialists, then do not forget that there is always a possibility of certain problems arising:

• Loss of official guarantee. Today, any change to the phone software entails loss of warranty.
• Inability to turn on the device. This can happen for various reasons. Perhaps something was installed incorrectly or the user made a mistake. However, there is no need to worry. As practice shows, the phone can almost always be revived without contacting a service center.

For the firmware to be installed successfully, perform all the steps described above carefully and carefully. In addition, you can always find a training video that shows the HTC flashing procedure step by step.

Instructions

Before flashing, download the latest software available for HTC Sensation. To download, you can use resources dedicated to working with software for this phone. After downloading the appropriate archive with the firmware, unpack it using an archiver program into a separate folder on your computer.

Download the Android SDK from the official Android website. Install the resulting software package using the installer. If you don't have HTC Sync installed on your computer, install it because... A package of all the necessary drivers for flashing is supplied with it.

Put your phone into Fastboot mode. To do this, turn off your HTC, then remove the battery and reinsert it into the device. Turn on your smartphone by simultaneously holding down the power button and the side volume down key. Wait for the boot options selection menu to appear. From the options offered, select Fastboot using the volume buttons. Confirm your choice by pressing the top power button.

Connect your smartphone to your computer and wait for the necessary drivers to unpack. Run the adb.exe program, which you can find in the folder with the Android management program (Start - Computer - Local Drive C: - Program Files - Android - SDK - WindowsPlatform - Tools - ADB). Adb.exe must be launched by right-clicking on the file and selecting “Run in command line”.

Type fastboot oem get_identifier_token and press Enter. Copy the key obtained as a result of the operation on the official HTC website in the device unlocking section, to access which you will need to go through the registration procedure by filling out the required fields. After moving to Step 10, paste the copied code from the command line into the appropriate section and click Submit.

Your phone will receive an unlock code in the unlock_code.bin format. Download this file and place it in the same directory where adb.exe is located. At the command prompt, enter fastboot flash unlocktoken unlock_code.bin. If the operation was performed correctly, you will see a corresponding message on the screen of your device. Select Yes.

fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot flash boot boot.img
fastboot flash userdata data.img
fastboot reboot

After entering these commands, the device will reboot and the new firmware will be installed on the device.

Helpful advice

Before flashing, save all your data on your computer, because during the installation of new software they will be lost. HTC Sync will help you save important data.

Sources:

• Android SDK
• HTC Sync
• how to reflash htc phone

HTC Sensation can automatically check for and notify the user when new Android operating system updates become available. You can download updates over Wi-Fi or your carrier's packet data service.

Instructions

Establish an Internet connection on your device. To do this, use a Wi-Fi hotspot or a 3G connection. You will have to download a fairly large amount of data, i.e. It is advisable that the traffic you receive is not charged.

When your internet connection is on, if there are updates available for your phone, you will see a notification on the screen. Confirm the installation of the software and wait for the updates to install.

If the message does not appear, pay attention to the top notification line of the screen. Click on the icon that appears in the line and select the update to download. Follow the onscreen instructions to begin downloading the software. After completing the operation, click on the “Install Now” button and then “OK”.

The HTC Desire S smartphone is already about 4 years old. Despite the long wait for the fourth version of Android, this device remained with Android 2.3.5 and Sense 3.0 on board. If you are still the owner of this device, then we are glad to present you with detailed instructions for updating to the unofficial version 4.2.2.

Today we are installing custom firmware, made by craftsmen, on one of the branded phones - NTS One X. We won’t bore you with an introductory lecture on firmware, but will immediately move on to step-by-step instructions that will update your phone. Phone firmware - step-by-step instructions You have not unlocked the NTS bootloader, then you are welcome, go to

In October 2012, HTC introduced and announced a new OS for its new products - Windows Phone 8. WP 7.8 was shown as a consolation prize for those smartphones for which the new operating system is “not suitable”. But, despite the announcement, the manufacturer was in no hurry to release new products. There were people

When approaching the issue of updating your gadget, you need to know in advance what results you need to achieve. If you own an HTC Wildfire S running Android 4.0, you can upgrade your mobile device by updating the operating system to the new version 4.1. Thus, we will not only improve the technical characteristics, but also get more installation options

If you are the happy owner of a modern, functional smartphone, then sooner or later your gadget will become morally and functionally obsolete. Buying every new flagship is quite expensive, especially if they come out with fantastic regularity. For this reason, many of us simply flash our smartphones to improve functionality. Unfortunately,

The HTC HD2 smartphone is unique because you can install any firmware on it, except iOS. In this article we will install Android firmware, and a little later we will look at installing Windows Phone on this device. For simplicity, I advise you to install the firmware from Cottula (download from the link), and I will install it. You can choose any

Most recently on the site developer.htc.com official firmware for HTC Desire. This update to version Android 2.3 Gingerbread Although it is available for download to anyone, it is not available from the update menu in the smartphone itself. This is due to the fact that Desire has a rather small amount of memory and the developers do not recommend upgrading to 2.3 ordinary users. The updated firmware is missing background images, the Facebook application and some programs HTC Sense.

1. Preparing the smartphone for firmware.

The first thing you need to do is save your contacts to a memory card. To do this, click on the screen "Telephone", go to the address book (where all contacts are displayed) and press the hardware button menu. From the menu that appears on the screen, select "Import Export" and choose "Export to SD card" and get the file on the flash drive "pcsc_pcsc_00001.vcf" or another type with an extension. vcf file.

We copy all the data from the SD card to a computer, just in case, because photos and possibly other necessary files are stored there. We format the SD card to delete all no longer needed data on the card. After all, all programs will have to be installed again, and they will create directories on the card for themselves. Let's go "Settings" — "Device memory" — "Remove memory card" — "Clear SD Card".

Reset HTC Desire before the initial settings, then all installed applications will naturally disappear, but the phone will immediately free up all possible free space in the memory of the device itself and there will be no problems if free space is needed during the firmware. So let's go to "Settings", Further "Device memory" and the lowest point will be "Factory reset". After the reset, I ended up with 136 megabytes of free space.

2. Download the firmware.

Well, of course, you need the firmware itself, download it either from our website using this link - or from the official HTC website.

After downloading, we see 4 files in the archive:

• Flashlight_signed_07072011.apk- flashlight
• teeter_signed_07072011.apk- ball game
• htc_wallpaper.zip– background pictures (archived)
• – the firmware itself (archived)

Because Android 2.3.3 takes up more space, then standard programs (flashlight and toy with a ball), as well as “wallpapers” were removed by HTC developers from the firmware and made into separate applications that can be installed if you still need them.

I'll get ahead of myself and say that after resetting to factory settings, the same android 2.2(official update) on my HTC Desire, 136 megabytes freed up. After updating to firmware 2.3.3 there was 128 megabytes of free space. I think you won’t be afraid of losing 8 megabytes of free space, because now almost all applications can be moved to an SD card.

3. What is needed?

Find and unpack the firmware itself ( HTC Desire Android 2.3 Upgrade.zip). There are 2 files inside, PDF instructions and EXE which is a self-extracting installer, after launching which, the firmware and flasher are unpacked into a temporary folder and automatically launched.

Let's see what the instructions recommend. The first point is the characteristics of the PC on which the firmware will be installed. At least a gigahertz processor, 512 MB of memory or more, 150 megabytes of free disk space and USB 2.0. Windows operating system, from XP Home to 7 Ultimate.

4. Connecting and setting up HTC Desire for firmware

Install HTC Sync, if you don't have it installed yet. If installed but not running, then launch it. Download HTC Sync you can from this site, via the link - or from saya.

We connect your HTC Desire USB cable to the computer, select synchronization on the display. If everything goes well, then HTC Sync will see the device on the computer. I advise you to connect it specifically to the system unit, because when connecting to the USB hub in the monitor, I got an error when flashing the firmware ( ERROR : USB CONNECTION ERROR), which reports an incorrect connection or driver problems.

We check that your computer does not go into sleep mode when inactive and after a certain number of minutes have passed. Well, I also advise you to remove the inclusion of the screensaver. Close all unnecessary programs on the computer.

Disable screen lock. Let's go to "Settings" — "Safety" — "Change blocking method" or ( "Set up screen lock") — "Unprotect".

Check the battery charge level (the official instructions recommend at least 30%). Let's go "Settings" — "About the phone" — "Battery".

Launch the flasher, file " RUU_HTC Desire Android 2.3 Upgrade (Gingerbread).exe»

Attention! Don't forget to save all data from your phone (contacts and files from the memory card). Do a factory reset and clear the memory card. And remember that after flashing all your data and settings will be reset.

The firmware installation takes about 10 minutes, do not pull the cable out of the phone or computer, do not press buttons on the phone and it is not recommended to use the computer, wait until the procedure is completed.

5. Updating HTC Desire to Android 2.3 Gingerbread (flasher instructions)

Once again, make sure that you have done a factory reset, which will remove all installed applications on your smartphone and reset the settings.

In the first window, simply click “ Next" In the next window, we are again warned that we need to delete all data from the phone and are asked to read ReadME (instructions in English).

The third window reminds you to disable Windows hibernation mode, battery charge level and check the USB cable connection.

We check the box and click “Next”, after which the connection of the smartphone to the computer and the status of the device are checked.

After a successful check, in the next window we see the “Update” button.

Click on this button and see in the next window the firmware version on the device and the version to which your Desire will be flashed, click “Next” again.

And the last window that appears, before the update process, tells us that by clicking the “Next” button, the process of flashing the device will begin, all information will be displayed on the screen, and upon completion we will receive a message about the successful update of the device. It’s not too late to refuse, but we click “Next” again.

Began! This is what all this was done for, the process of updating your HTC Desire to Android 2.3.3 has begun

It all looks like a small window with a progress bar, a message that the process will take about 10 minutes, under no circumstances touch the USB cable connecting the smartphone to the PC.

Upon completion, we receive a window with a “Finish” button and a message in English that the process has been successfully completed.

Hooray! Now yours HTC Desire works under Android 2.3.3

We restore contacts and necessary data from backups and reinstall the necessary applications.

Possible error messages:

ERROR : FILE OPEN ERROR– file reading error, try running “RUU_HTC Desire Android 2.3 Upgrade (Gingerbread).exe” again

ERROR: MAIN BATTERY POWER– the smartphone battery charge is less than 30%, put it on charge and try it when the battery is sufficiently charged.

ERROR : MODEL ID ERROR

ERROR : CUSTOMER ID ERROR– the firmware is not intended for your smartphone model.

ERROR : IMAGE ERROR– the firmware file is incorrect or damaged, try downloading the firmware again from the website.

ERROR : USB CONNECTION ERROR– USB cable connection error. Connect the cable directly to the computer, not to USB hubs.